Page 6 - Product Catalogue

Ceramic Adhesives

YURTBAY SUPER FIX

CERAMIC TILE AND GLASS MOSAIC ADHESIVE MORTAR
YURTBAY SUPERFIX is a cement based, standard performance
ceramic adhesive mortar, with reduced slip, extended open time.

C1TE
TS EN 12004-1
FIELDS OF APPLICATION APPLICATION REQUIREMENTS
Used in horizontal and vertical application of small and medium • The ambient and substrate temperature should be in the range
size floor, wall ceramic, natural stone tiles in Interior and exterior of +5 °C to 35 °C.
spaces. • Should not be applied on frozen, thawing surfaces and surfaces
APPLICATION EXAMPLES with a frost hazard.
Interior wall: Cement based coating, plaster and concrete floors • Application should not be made when the substrate temperature
Interior floor: Cement based screed substrates (provided that they is high, and during very sunny or extremely windy weather.
are adequately set and dry) and concrete floors WARNINGS AND RECOMMENDATIONS
Exteriors: Cement based screed and concrete substrates • If crusting occurs on the material during open time, the material
APPLICATION DATA (23 °C & 50% B.N) should be applied after being re-mixed.
Product type : Powder • It is not recommended to re-wet the material if there is crusting
Product color : Gray and white in the material.
Mixing ratio : 5,75-6,25 L water for 25 kg mixture • Any foreign substances should absolutely not be added.
Pot life : Max. 3 hours • Recommended for ceramic applications up to 33x33 cm.
Application temperature : between +5 °C +35 °C • Gypsum and similar surfaces with high water absorption should be
Open time : 30 minutes (as per TS EN 12004-1) primed before application to reduce water absorption.
Ready for Use : Min. 24 hours (light pedestrian traffic) CONSUMPTION
Required time for grouting : Min. 24 hours Consumption amount per 1 m .
2
Full setting duration : 28 days
SURFACE PREPARATION Application Notch Size Consumption Amount (Kg/m )
2
Substrates on which application will be made should be clean and One-sided adhesion 6x6x6 mm 3-4 kg
sound. Any dust, oil, dirt and materials that will prevent adhesion One-sided adhesion 8x8x8 4-5 kg
should be removed from the surface and mortar, cement, etc.
residues should be scraped off. Surface defects with depth more Note: Provided consumption values are approximate values, and
than 2 cm should be repaired at least 1 day in advance. may vary depending on the area of the application surface and the
MIXTURE PREPARATION application thickness.
Clean water of 5,75-6,25 L is poured into a clean, round container; SHELF LIFE
then, a 25 kg powder product should be added slowly and mixed 12 months from production date when stored in non-humid, dry
until a homogeneous, pellet free appearance is obtained environments and in original packing.
. mixing should be made using a low speed mixer. The fresh The packages should be tightly closed when not in use.
mixture should be allowed to mature for 5 min, and re-mixed prior *These values have been obtained as a result of laboratory tests
to application. in compliance with the standards. The values may vary in different
APPLICATION application environments.
The mixed YURTBAY SUPERFIX mortar should be applied on
the substrate using a steel notched trowel, with a notch size BAG PALLET
appropriate to the tile dimensions. The coating material is placed Bag Weight / kg AMOUNT / BAG GROSS WEIGHT / kg SIZE / cm
on the surface and ensured to be fitted on the surface using 25 54 1370 80x110x105
a rubber mallet. Adhesive mortar should also be filled into the
bottom holes of the tiles, in bonding the tiles larger than 20x20
cm in exterior applications. the tiles should be adhered to the
surface within 30 min. Wide expansion joints are required to
be left for every 50 m² during application. The prepared mortar
should be used up within 3 hours.

3